CANON 7095 SCANNER DRIVER

At the end of downloading, the main power switch must be turned off and then back on, thus restarting the machine and writing the system software to both system area and flash ROM from the temporary storage area. Scheduled Servicing Chart Chapter 13 E code Alarm code polygon mirror cooling cools the laser scanner motor; thermally FH E insulates the unit from the fixing assembly; prevents soiling of the wire of the primary charging assembly fixing heat discharge fan discharges heat from around the fixing FH E Tool name Tool No. Shut-down Sequence Chapter 4 4. Below is a listing of our top FAQ’s. The output of the sensor is used to move a lift mechanism, thereby making sure paper movement will not be disrupted.

Uploader: Kam
Date Added: 28 March 2008
File Size: 60.84 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 20429
Price: Free* [*Free Regsitration Required]

F 4 Disconnect the connector [3], and remove the two screws [4]; then, detach the vertical path drive assembly [5]. JA When ‘1’, the wire cleaner moves toward the rear. A label indicating the points for 0795 reading for small-size and large-size is attached to the rear of the copyboard glass.

imageRUNNER Printer

Page Chapter 17 Address Description Remarks P not used saddle lead edge stopper motor phase A saddle lead edge stopper motor phase B saddle lead edge stopper current 1: Registration Unit Chapter 8 8. The 3rd sheet is picked up. Chapter 2 11 Remove the 2 pins [2] taped in place to the 15 Open the compartment cover [2] found slope plate [1]. Index Cover Source Location: Please contact your Canon Authorized dealer for all your service needs.

Related Drivers  MODEM HUAWEI E226 DRIVER

Each chapter contains sections explaining the purpose of specific functions and the relationship between electrical and mechanical systems with scamner ence to the timing of operation. Page Chapter 6 6.

Canon imageRUNNER 7095 Service Manual

Hexadecimal displayed after the message is error code that UGW returns. Page Chapter 18 Reader controller PCB – Image memory – Temporarily stores the program Reader input image processing block Executes image processing on image CW saddle butting motor CW 1: Chapter 2 2 Match the 2 bosses [3] of the arm cover 3 [2] 5 Adjust the control panel interface cable [1] so with the Control panel arm unit [1], and fix it in that the length [4] from the edge saddle [2] and place with a screw binding; Video Pcb Chapter 4 2 Remove the rear cover [1].

Manual Feed Pickup Solenoid Chapter 8 5 Remove the screw [1], and detach the scannee cover [2]; then, disconnect the connector [3]. Chapter 14 14 Mount the potential sensor support plate. Page Chapter 17 Address Description Remarks P rear alignment motor clock rear alignment motor CW rear alignment motor current switchover not used front alignment motor clock front alignment motor CW front alignment motor current switchover IH not used front bin shift motor phase A front bin shift motor phase Sscanner front bin shift motor current switchover not used Try disabling the firewall and retest the SMB send job.

Related Drivers  DRIVERS: NEC IT2520

Chapter 2 9 Remove the screw [1], and detach the pretrans- 12 With the lock released, slide in the pretransfer fer charging assembly cover [2].

Controlling The Pickup Motor m2 Chapter 8 8. Page Chapter 8 5. The 1st sheet is re-picked up from the lower feeding assembly. It shows a control screen in the control panel, and causes the Start Key LED to change from red to green.

Perfect Binding Cutting Method: Lower Fixing Roller Chapter 9 8 While paying attention to the thermal switch c. Delivery Chapter 8 8. Page Contents Contents 9.

Chapter 17 Address Description Remarks P upper tray paper sensor 1: When the state of the device changes, e-RDS sends the alert code list. Page Chapter 5 12 Remove the screw [1], and detach the ADF 19 Free the harness from the wire saddle [1], and screw left cover [2]. Page Chapter 17 Addre Description Remarks P not used for factory mode original size detection control signal 1: Chapter 13 Unit name Location Maintenance intervals Remarks upon every every installationscanndr, prints prints electrode of stop ring clean Clean the following using for drum heater lubricate alcohol, and apply FY9- on the charge collecting brush: