K7VM2 USB DRIVER

Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components. If the jumpers JL1 and JR1 are short see fig. Please check if the CPU fan on the motherboard functions properly before you resume the system. If both jumper caps on JL1 and JR1 are removed see fig. There are 2 ways for you to clear and reset the system parameters to the default setup. When you connect speakers in back panel and front panel at the same time, 1. It’s a community-based project which helps to repair anything.

Uploader: Kigazilkree
Date Added: 3 June 2013
File Size: 13.80 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 26991
Price: Free* [*Free Regsitration Required]

Unplug the power cord from the wall socket before touching any component.

Asrock K7VM2 V3.X Motherboard socket A 462 AGP VGA 2x PCI AMR LAN IDE USB DDR RAM

Micro ATX form factor 9. The Support CD that came with the motherboard contains necessary drivers and useful utilities that will enhance motherboard features. No part of this installation guide may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.

Keep the screws for later use. To improve heat dissipation, remember to spray thermal grease between the CPU and the heatsink when you install the PC system. Match the red marking on the floppy ribbon cable with Pin1. To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the like.

Related Drivers  LASERJET 4000N DRIVERS FOR WINDOWS MAC

Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components. It’s a community-based project which helps to repair anything. DO NOT place jumper caps over these connectors. Unlock a DIMM slot by pressing the retaining clips outward.

Asrock K7VM2 Motherboard Boot – Questions (with Pictures) – Fixya

Hold components by the edges and do not touch the ICs 4. In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages including damages for loss of profits, loss of business, loss of data, interruption of business and the likeeven if ASRock has been advised of the possibility of such damages arising from any defect or error in the guide or product.

This Quick Installation Guide contains introduction of the hsb and step-bystep installation guide for new DIY system builders. For detailed information, please refer to page 13 of user Manual in the Support CD. You isb find the file in the Support CD through the following path: Fasten the card to the chassis with screws. More detailed information of the motherboard can be found in the user manual enclosed in the product CD-ROM.

The data in CMOS includes system k7vm information such as system password, date, time, and system setup parameters.

Please remember to remove the paper clip or the jumper cap after clearing the CMOS. If the jumpers JL1 and JR1 are short ub fig. For proper installation, please kindly refer to the instruction manuals of your CPU fan and heatsink vendors. While CPU overheat is detected, the system will automatically shutdown. Installing an expansion card Step 1.

Related Drivers  ASUS P5L-MX AUDIO DRIVER

K77vm2 lever clicks on the side tab to indicate that it is locked. Please follow the figures above to set the CPU front side bus frequency. The setting of the CPU front side bus frequency of this motherboard is by means of the adjustment of jumper-setting.

However, it requires your front panel to support the function. ASRock assumes no responsibility for any errors or omissions that may appear in this guide.

USB Audio Device driver free download for windows – VIA – K7VM2

Power Management for USB 2. Before installing the expansion card, read the documentation of the expansion card and make necessary hardware settings for the card.

It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance. There are 2 ways for you to clear and reset the system parameters to the default setup. Remove the bracket facing the slot that you intend to use. If both jumper caps on JL1 and JR1 are removed see fig.